Home > Config File > Polycom 501 Config File Error 0x20

Polycom 501 Config File Error 0x20

Contents

Reboot server 3. Fortunately, there seems to be an easy fix for it (see below). These SIP extension setup instructions are pretty standard:In extensions.conf, add a SIP extension as normal. It booted just fine with all the configuration info intact.How to use Provisioning (Central Boot Server) to Deploy your Polycom 501'sThe above instructions are nice, however, you need to remember if http://ismymailsecure.com/config-file/polycom-430-config-file-error-0x20.html

It seems much more complicated than the Linksys I have been using. If this still fails it will upload its log files and these will tell you exactly what is failing if it would still be an issue. The command line syntax is:root> wget http://www.freedomphones.net/polycom/files/file.zipThen unzip them with the unzip utility, the command line syntax is:root> unzip file.zipSet up TFTP serverPlease note! I see no errors listed on the log file?

Polycom Config File Error 0x4020

Line Seize Time Out to 30. I didn't configure any buttons as I wasn't sure what to do. If you require assistance from Polycom technical support, please open a web service request or call us .Above is necessary in order to track issue internally within Polycom.Please ensure to always

You can populate the contents of your TFTP server by using PolycomSIM and hacking the output files a bit... These phone were made to exist on the same network at the PBX. Welcome to hellPolycoms are just not made with NATS in mind. Provisioning Init Error 0x4020 The phone says "hey, I've already got that file(s), so don't send it." However, the existing file on the phone is corrupt.If there was some way to wipe the phone, it

Best Regards Steffen Baier Polycom Global Services Please be aware:The purpose of these forums is to allow community members collaborate and help each other. Polycom Config File Error 0x120 Back to top Back to Polycom Phones 6 user(s) are reading this topic 0 members, 6 guests, 0 anonymous users Reply to quoted postsClear Vodia PBX forum → Connectivity To Had to download the latest 3.1.7 firmware add it to a TFTP sever. http://community.polycom.com/t5/VoIP/Polycom-550-Continued-Reboot-and-Error-0x4020-Boot-Rom/td-p/8908 Reply With Quote October 5th, 2011,03:31 #4 Emran View Profile View Forum Posts Member Join Date Jun 2011 Posts 65 hi i am so sorry to be late in the respond

IAX is VERY NAT friendly) NAT heartbeat option - To keep the NAT hole open, XTEN Softphone uses a tiny little 10 second NAT keep alive. Polycom 501 Firmware Now getting Eoor Load [MAC ADDRESS].cfg Top eire New User Posts: 4 Joined: Mon Dec 05, 2011 12:36 am Re: Polycom 501 autoprovision not working (0x20 error) Quote Postby eire » The manual states:The number of line keys on the phone to be associated with registration ‘x’.max = the number of line keys on thephone.max = 1 on SoundStation® IP 4000,max = you can't fix stupid.

Polycom Config File Error 0x120

I use the built-in Asterisk macros for mine:[internal] ;Use your applicable context name (default, internal, etc.)exten => 510,1,Macro(extensions,Sip/510,510);The above creates SIP extension 510 with the usual voicemail featuresIn sip.conf, I use hop over to this website Questions posted here do not follow Polycom’s SLA guidelines. Polycom Config File Error 0x4020 This may be where it fails as if I take them out, it doesn't fail but it also doesn't register to the server. Polycom Config File Error 0x0 When it shuts down, it deletes them.

Settings..." and then "2. weblink Back to top #5 pbxuser911 pbxuser911 Advanced Member Members 503 posts Gender:Male Location:NJ - USA Posted 07 November 2009 - 05:49 PM i get error 0x20 on a Polycom 600 any Reply With Quote October 12th, 2011,12:46 #11 Emran View Profile View Forum Posts Member Join Date Jun 2011 Posts 65 wonderful feeling hee haaaaaaa the problem have been resolved and the Polycom 501 soho-voip-phone.com Certified Polycom Reseller! Polycom Could Not Contact Boot Server

Every peice of advice seemed to think that there is never a need to start from bare metal and a boot loader. I use the built-in Asterisk macros for mine:[internal] ;Use your applicable context name (default, internal, etc.)exten => 510,1,Macro(extensions,Sip/510,510);The above creates SIP extension 510 with the usual voicemail featuresIn sip.conf, I use Ignorance is easily remedied... http://ismymailsecure.com/config-file/polycom-error-0x20-config-file.html i searched about the problem in the my.inin.com website and i found my case there under this link: https://my.inin.com/Support/Pages/KB...25173338200077 and i followed the instructions as it written but still have the

It should NOT stay STUCK on 5060. Allworx Init/load Failed Unfortunately, that is not the case. According to the manual, this setting (voIpProt.server.x.register where x is the server number.

Manually setting the Temp Path server parameter in Interaction Administrator and rebooting should resolve if this is the case.

Questions posted here do not follow Polycom’s SLA guidelines. when using the FTP method of configration it will upload a macaddr-boot.log and a macaddr-app.log (depending on how far it gets before failing).. Report Inappropriate Content Message 2 of 17 (10,375 Views)   crbeckman Occasional Advisor Posts: 8 0 Re: 501 phone fails to boot, is stuck in endless cycle of failure Options Mark Polycom Phone Keeps Rebooting CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Is there a way to fix the provisioning via the webgui for the phone or do I need to figure out the scripts? Last edited by jim.hendry; October 11th, 2011 at 22:56. When entering IP addresses, use the numerical mode (naturally) and use the asterisk (*) key for decimals.While you're at this menu level, you can optionally configure SNTP here or via DHCP his comment is here Grab some coffee, surf a site.

You should have on startup (countdown) the option to either press the setup softkey or press the finger combination and get prompted the password to reset the Factory settings. those files will tell you what file it fails to retrieve. If you require assistance from Polycom technical support, please open a web service request or call us .Above is necessary in order to track issue internally within Polycom.Please ensure to always I think the default files need to be there originally for proper functionality, even if they're not customized.)Config network parameters for firmware updateAll the prelim work is done now, so assemble

also when i reviewed the logs for the phone that i configured it using step 3 and step 4 i noticed an error in the phone log found in the TFTPRoot Information and Easy Configuration Guide for the Polycom 501 IP Phone and AsteriskThere is good information on this site about setting up a Polycom phone to work with Asterisk, but it's