Home > Post Error > Post Error 162

Post Error 162

Contents

Reseat fan cable. Numeric Codes and Text Messages Control panel message Description Recommended action 101-Option ROM Checksum Error System ROM or expansion board option ROM checksum. I'll let you know if it works as soon as I have visited my daughter at Uni (which is where the computer is now). Internal PXE option ROM is used for booting from the NIC to a PXE server. 162-System Options Not Set Configuration incorrect. his comment is here

Check the event log for uncorrected DIMM failure events. 00580A1 Invalid DIMM population for mirroring mode Note: Each time you install or remove a DIMM, you must disconnect the server from If the error persists, update to the latest BIOS version and ME firmware version. When using the local console: Run the Setup utility. Reseat chassis, rear chassis, or front chassis fan.

162 Configuration Error Ibm Server X3650

Remove any recently installed hardware. 3038003 Firmware corrupted Run the Setup utility, select Load Default Settings, and save the settings to recover the server firmware. (Trained service technician only) Replace the Check that both power supply cables are properly connected to the system board. If additional memory was recently added, remove it to see if the problem remains.

This page is rather extensive and will be updated on a regular basis. Replace CPU fan. 512-Chassis, Rear Chassis, or Front Chassis Fan not Detected Chassis, rear chassis, or front chassis fan is not connected or may have malfunctioned. Replace the following components one at a time, in the following order, restarting the server after each one: Battery (Trained service technician only) System board. 2011001 PCI-X SERR Check the riser-card Parity Error Message Replace the system board.

None Green Power LED flashes every two seconds. 162 Configuration Change Has Occurred Ibm Server Red Power LED flashes eleven times, once every second, followed by a two second pause. Note: Each time you install or remove a DIMM, you must disconnect the server from the power source; then, wait 10 seconds before restarting the server. https://support.lenovo.com/us/en/documents/ht073271 Ensure that none of the keys are depressed.

Reseat front chassis fan. Ibm Post Error Codes Replace DIMM with a module conforming to the SPD standard. 214-DIMM Configuration Warning Populated DIMM Configuration is not optimized. Disable TXT in the Computer Setup (F10) utility. Check product documentation for memory support information. 301-Keyboard Error Keyboard failure.

162 Configuration Change Has Occurred Ibm Server

Make sure one or more DIMMs are installed in the server. https://community.hpe.com/t5/ProLiant-Servers-ML-DL-SL/POST-Error-162-System-Options-not-set-in-Proliant-3000/td-p/3375554 Ask the community! 162 Configuration Error Ibm Server X3650 Basically, the device information is different from what the BIOS is expecting. Ibm Error Codes Check to see if the 5V_aux light on the system board is turned on.

Power-on external devices first, then power-on computer. 4. this content Find Solutions, ask questions, and share advice with other HP product owners. Reseat the following components one at a time in the order shown, restarting the server each time: Battery Failing device (if the device is a FRU, then it must be reseated If the hard drive LED turns green, the power button is working correctly. How Many Digits Are In A Mac Address?

not quite the 6 gig that was in there, but it will do... Disconnect any other diskette controller devices (tape drives). the HD makes a wied whining sound when i do a c:\dir , and it "an error occured during dicrectory enumeration." the hard drive is fucked i guess.. weblink If you do you will need to disable one, preferalbly disable the serial mouse and enable the PS/2 Slot.

To manually switch to the POST Messages Enabled mode during POST, press any key (except F10, F11, or F12). What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable? Restart the server. 3818001 Core Root of Trust Measurement (CRTM) update failed Run the Setup utility, select Load Default Settings, and save the settings. (Trained service technician only) Replace the system Make sure that the operating system is not corrupted.

The only problem is that whenever I boot, I get a 162 Configuration error, and I have to reset the BIOS settings.

Reboot the computer. If the system enters the POST, then power off and replace one device at a time and repeat this procedure until failure occurs. Invalid Electronic Serial Number Electronic serial number is missing. One Long Beep Followed By Three Short Beeps RTC (real-time clock) battery may need to be replaced.

Make sure the DIMM is installed correctly (see Installing a DIMM). Open hood and check that the power button harness is properly connected to the system board. None required. http://ismymailsecure.com/post-error/post-error-200-299.html and i have no idea how to get the mother or daugther boards out..

If an action step is preceded by "(Trained service technician only)," that step must be performed only by a trained service technician. See the Hardware Reference Guide for instructions on installing a new battery, or contact an authorized dealer or reseller for RTC battery replacement. 163-Time & Date Not Set CMOS jumper may If possible, rearrange the order of the adapters in the PCI slots to change the load order of the optional-device ROM code. Reseat all affected adapters and riser cards.

Let me know and I'll get it corrected as soon as I can. Quick Boot is a fast startup process that does not run all of the system level tests, such as the memory test. Clear CMOS. (See Appendix B, Password Security and Resetting CMOS.) 660-Display cache is detected unreliable Integrated graphics controller display cache is not working properly and will be disabled. If the DIMM was disabled because of a memory fault, follow the suggested actions for that error event and restart the server.

Beeps stop after fifth iteration but LEDs continue until problem is solved. 3 Processor not installed (not an indicator of bad processor). Privacy Policy © Copyright 2016 HP Development Company, L.P. and the front case fan is dead, well.. the computer only has 1 ide channel too..

Run the Setup utility, select Load Default Settings, and save the settings. 3808000 IMM communication failure Shut down the system and remove the power cords from the server for 30 seconds; The first part of the error code indicates the device that is causing the trouble. Open the hood and ensure the 4 or 6-wire power supply cable is seated into the connector on the system board. Power on the system.

edit again.. Make sure a DIMM is installed in the black DIMM connector first if there is only one DIMM in the system. Beeps stop after fifth iteration but LEDs continue until problem is solved. 4 Power failure (power supply is overloaded). If the error still persists, replace the system board. 2240-ME image unlock failure Special system configurations with reduced ME firmware image require BIOS control of ME firmware upgrading.

If fan is plugged in, but is not spinning, then replace heatsink/fan assembly. The drivers and installation seemed to go fine, but I could not attach to the network. (The card etc is compatible).