Home > Post Error > Post Error 1724-drive Array

Post Error 1724-drive Array

The maximum number of logical drives supported is 32. Call the Compaq service provider. 219 - Snoop Rules SRAM Failure. None Incorrect cabling. I do not see any errors listed in the ADU, BUT there are also no drives attached to the SA6400 controller. http://ismymailsecure.com/post-error/post-error-1784-drive-array-drive-failure-hp.html

Back up data before replacing drive(s)if using RAID 0. Replace the failed fan. 1612 - Primary power supply failure. 2 short Primary power supply has failed. You might need Ontrack to recover the data. Download the Diagnostics Utility and System Configuration Utility from this page.

Any drives with failed lights? 0 Kudos Reply Rejeesh Radhakrishnan Occasional Visitor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content This is how we thank each other in the forumhttp://forums11.itrc.hp.com/service/forums/helptips.do?#33Regards. __________________________________________________How to assign points on this new forum? However, others are related to Compaq-specific hardware. STEP 2:Click the "Quick Scan" button.

Replace the PPM to restore redundancy. 216 - Processor PPM has lost Redundancy Module X None Indicated PPM (DC-DC Converter) has lost redundancy. The fact there are no drives attached to it and there are also no errors would likely mean that whatever used to be attached to that controller is not being detected.The How were they configured? Check PCI hot plug enabler connectors.

Run diagnostics and replace failed processor. 214 - DC-DC Converter Failed None PowerSafe Module (DC-DC Converter) failed. Check and replace missing or failed controller assembly. 1618 - PCI slots powered down. Reseat every drive and make sure they are properly mounted. learn this here now Are all of them healthy?

Select F1 key to resume. Do you see all the drives in the enclosure? The model and firmware of that disk are the same as the disk it is mirrored with, and that disk's ID is correct. I can see 2 connection ports on the Disk array and I am also thinking about to connect through the other port which we are not using now, is that make

Check Cache Accelerator installation and if properly installed, replace. 221 - Power Fault On Processor Bus X None A PPM on indicated bus is in a failed state. Turn off the computer, then reconnect the keyboard. 301- Keyboard Error or Test Fixture Installed None Keyboard failure. POST Power-On-Self-Test (POST) is a series of diagnostic tests that run automatically when the system is turned on (small program contained in the BIOS). Replace failed assembly as indicated. 162 - System Options Not Set 2 short Configuration incorrect.

Jc Says: at 4:48 AM worked just like it said. this content McKenney Respected Contributor [Founder] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎02-14-2011 07:04 PM ‎02-14-2011 07:04 PM Re: 1724-Drive I am pretty sure that we reconected every think correct as before and nothing happened to the array while moving it. The system returned: (22) Invalid argument The remote host or network may be down.

Run Diagnostics. Backup the data.3. Please go to HP Support Center. http://ismymailsecure.com/post-error/post-error-1784-drive-array-drive-failure.html delete the affectet logical drive / array.4.

Upgrade FW.Most likely won't help. Replace failed assembly as indicated. 207 - Invalid Memory Configuration - check DIMM (SIMM) Installation None Memory module installed incorrectly. Please look into updating the firmware of the Smart Array controller if that has not been done.Regards, 0 Kudos Reply The opinions expressed above are the personal opinions of the authors,

Generated Mon, 24 Oct 2016 08:27:08 GMT by s_wx1062 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection

All rights reserved. None Cache Accelerator in slot x improperly installed or bad. System halted. Watch the drives spin up.

Run the System Configuration Utility and correct. 1610 - Temperature violation detected. System Halted None Catastrophic chipset failure. Simply click the links below for your free download. http://ismymailsecure.com/post-error/post-error-1797-drive-array-array-accelerator-read-error-occurred.html I'm not a PC guru by any stretch, but this was a godsend.

Replace the keyboard. SA card's firmware is at v2.58, and all hard drives are up-to-date on firmware. Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions. Check and replace failed controller assembly. 1617 - I/O Fan controller not responding. 2 short I/O fan controller failure.

Run Diagnostics. Not sure if the last disk showed that ID 13 before or not.Wondering primarily why I would see the POST 1724 error (if no disks have been moved/removed), and secondarily why Try to free it. 2. I'll check.Thanks again .

Community ProLiant Servers (ML,DL,SL) CommunityCategoryBoardUsers turn on suggestions Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as What is the error? Replace failed assembly as indicated. 1615 - Power Supply Failure, Power Supply Unplugged, or Power Supply Fan Failure in Bay X. This POST message goes away and performance of the controller improves after the parity data is initialized by ARM (an automatic process that runs in the background on the controller). 1730

The P800 you have installed sees all of the drives in the MSA60 (12 x 1 TB drives), but whatever was attached to the SA6400 is no longer seen. Maybe one came loose. Showing results for  Search instead for  Do you mean  Menu Categories Solutions IT Transformation Internet of Things Topics Big Data Cloud Security Infrastructure Strategy and Technology Products Cloud Integrated Systems Networking Run diagnostics.

Run the System Configuration Utility and correct. 1152 - Com Port 2, 3, or 4 Address Assignment Conflict 2 short Both external and internal serial ports are assigned to COM2, COM3, If the drive is part of a nonfault-tolerant configuration, back up all data before you replace the drive and restore all data afterward. no more errors and officially back in action. Replace the part indicated. 40X - Parallel Port X Address Assignment Conflict 2 short Both external and internal ports are assigned to parallel port X.

If your network is live, make sure that you understand the potential impact of any command. None Normal operation. None The system has detected that the array enabler board is not installed.