Home > Post Error > Post Error 1787-drive Array Operating In Interim Recovery Mode

Post Error 1787-drive Array Operating In Interim Recovery Mode

if (λ x . More detail is provided below. WindowsNetworking.com Windows Server 2008 / 2003 & Windows 7 networking resource site. Magalhaes Thomas Shinder Brien Posey Deb Shinder Justin Troutman Mitch Tulloch Robert J. his comment is here

Powered by phpBB SysAdmin's Diary Through passion, I gain strength. Data will be automatically restored to drive X when a failed drive has been replaced, or to the original drive if it is working again without errors. troubleshooting flowchartspage 17................................................................................................................................................................ Restore password × Upload manual upload from disk upload from url Thank you for your help!

Is there something else that needs to be done for the changes to be recognised? –user151520 Jan 6 '13 at 19:55 To ewwhite. Refer to the following message. 1786-Slot 1 Drive Array Recovery Needed. HP websitepage 69................................................................................................................................................................ Are illegal immigrants more likely to commit crimes?

To print the manual completely, please, download it. Introductionpage 10................................................................................................................................................................ Previous page Next page 1...270271272273274 Also See for HP ProLiant ML370 Generation 4 HP HP ProLight Server Troubleshooting Manual 152 pages HP ProLiant ML370 Generation 5 User Manual 135 pages The two remaining drives show up as unassigned in the Array Configuration Utility.

When you are running W2K8 the raid firmware should have been updated to at least a 2009 version or you are in real trouble. –Tonny Jan 6 '13 at 22:26 Their last firmware updates occurred in 2008. –ewwhite Jan 6 '13 at 22:34 @user151520 I imported your data into the question. –sysadmin1138♦ Jan 8 '13 at 1:50 If the rebuild was aborted due to a read error from another physical drive in the array, back up all readable data on the array, run ADU, and then restore the http://systemmanager.ru/c00724721.en/10969.htm You need to replace it with a new one.

x x) has a type, then is the type system inconsistent? Why did they bring C3PO to Jabba's palace and other dangerous missions? Action: • Perform one of the suggested actions: − − • If drive recovery is not successful, run ADU ("Array Diagnostic Utility" on page 126) for more information. − − 1787-Drive There is a HP Utility Array Configuration Utility which was installed to see the RAID configuration from the OS.

The drives are offline. Select F1 to continue – drive array will remain disabled. By using this site, you accept the Terms of Use and Rules of Participation. End of content United StatesHewlett Packard Enterprise International CorporateCorporateAccessibilityCareersContact UsCorporate ResponsibilityEventsHewlett Packard LabsInvestor RelationsLeadershipNewsroomSitemapPartnersPartnersFind a PartnerPartner If the replacement drive failed, replace with another drive.

What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? http://ismymailsecure.com/post-error/post-error-1784-drive-array-drive-failure.html Too lazy to go to datacenter, I'm just using HP utility to confirm. The drives are of different types. Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands HP Manuals Server ProLiant series Troubleshooting manual HP ProLiant series Troubleshooting Manual: Drive Array Operating In Interim Recovery

Chassis Slot: 1 Hardware Revision: Rev B Firmware Version: 2.32 Rebuild Priority: Low Expand Priority: Low Surface Scan Delay: 15 sec Cache Board Present: True Cache Status: Disabled Accelerator Ratio: 50/50 Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. But all you need to do is mark one of the unused drives as a spare to the array, the controller will seize the new spare for the array and start weblink Network Security Tools Network Access Control Network Auditing Patch Management Portable Storage Security Security Scanners VPNs Web Application Security Web Content Security WhitePapers Featured Products TechGenix Sites ISAserver.org The No.1 Forefront

Audible Beeps: None Possible Cause: • Replacement drives may have been installed in the wrong drive bays. • A bad power cable connection to the drive, noise on the data cable, If the disk fails again, exchange it!greetings,Michaelps. so, if, your array is not going to rebuild process ( you will see a message on POST for this) even after removing and reinserting the drive, you should replace the

Select F2 to continue without starting Automatic Data Recovery.

If the replacement drive failed, replace with another drive. I did remove the drive marked as failed and replaced it with one of the unassigned drives but this didnt appear to make any difference at all based according to the Data will be automatically restored to drive X when a failed drive has been replaced, or to the original drive if it is working again without errors. Following a system restart, this message notes that drive X is defective and fault tolerance is being used.

MSPAnswers.com Resource site for Managed Service Providers. Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Was Sigmund Freud "deathly afraid" of the number 62? check over here Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands HP Manuals Server ProLiant ML370 Generation 6 Reference and troubleshooting manual HP ProLiant ML370 Generation 4 Reference And

Sign In Upload Page of 152 Go Download Table of ContentsContents TroubleshootingTroublesh.. WServerNews.com The largest Windows Server focused newsletter worldwide. Press the F2 key to continue without recovery of data to the drive. What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account?

in attach the Array Configuration utility page shown !in the system event viewer i find only this message:Physical Drive inserted : SCSI Port 2, ID 0, of Embedded Controller.I don't know